Use the following procedures to Factory Reset your JBL Professional powered speaker:
With the unit powered ON:
Press and hold CH1 and CH2 until the LCD powers off.
With the unit powered ON:
Press and hold MAIN/MENU and BACK until the LCD screen turns off.
With the unit powered On:
Press and hold MAIN and CH4 until all Channels Flash.
With the unit powered ON:
Press and hold PHANTOM and DUCKING until all Channels Flash.
With the unit powered On:
Press and hold BLUETOOTH until Power and EQ Presets Flash.
With the unit powered On:
Press and hold X-OVER and POLARITY until all LEDs Flash, sub will power off.
With the unit powered ON:
Press and hold PHANTOM 48V and DUCKING until all LEDs flash and unit reboots.
With the unit powered ON:
Press and hold Main/Menu and BACK until the LCD screen turns off .
With the unit powered On:
Press and hold MASTER and BACK until all Channels Flash.
With the unit powered OFF:
Press and hold BACK and MENU
While pressing and holding power ON, continue to hold until “FACTORY_RESET” appears on the LCD Screen.
With the unit powered OFF:
Press and hold BOOT and EQ+ while pressing and holding power ON, continue to hold until all EQ Presets Flash.
With the unit powered OFF:
Press and hold the Upper Left Button (NORM/BOOST, MAIN/MON or POLARITY) while pressing and holding power ON, continue to hold for 5 seconds.
The content provided is offered in good faith. While JPRO strives to provide accurate and helpful information, we cannot be held liable if the provided content does not successfully resolve an issue or offer a solution to a problem.
Information provided by Factory Reset for JBL Powered Speakers
How to configure CISCO SG300 network switch with Dolby processor and JBL DSI 2.0 amplifiers.
Any Managed Network Switch will work as long as it configured for Professional use and configured to allow Audio Video based on Dante requirements except for a small change in the QoS settings.
– The QoS/DSCP priority for Dolby AES67 is slightly different from Dante (Shown on last 2 pages of attached document)
– HP/Aruba Switches can also be configured in a similar method
The content provided is offered in good faith. While JPRO strives to provide accurate and helpful information, we cannot be held liable if the provided content does not successfully resolve an issue or offer a solution to a problem.
Control Contractor FIR Tunings Now Available
JBL has made available FIR tunings for select Control Contractor Series loudspeakers. The FIR filters optimise both frequency response and phase response to a finer degree of precision than has typically been possible with standard IIR “parameter-based” filters. Additionally, these FIR filters were designed to meet JBL Pro’s new V6 FIR tuning standard.
V6 Tuning Features:
V6 FIR Tunings Available For Loudspeaker Models:
The content provided is offered in good faith. While JPRO strives to provide accurate and helpful information, we cannot be held liable if the provided content does not successfully resolve an issue or offer a solution to a problem.
JBL IRX Auto Power Off Bypass
When you purchase an IRX108BT or IRX112BT the unit will power off by itself if it is idle for a few hours. The default status in the firmware is to go into standby mode automatically.
More details here:
https://help.harmanpro.com/irx-series-standby-mode-and-bluetooth-functions
https://help.harmanpro.com/how-to-disable-auto-standby-for-irx-series
As of September 2023, from firmware V6.0 (IRX108 IRX112) JBL Professional has added a disable/enable function.
To disable auto-standby mode:
If this procedure does not work, it means the Firmware on the IRX is too old and you will need to book a JPRO Service Request to update the firmware. The Service Request is done by requesting a a JPRO SRA ticket via our online portal using the link on this page.
The content provided is supplied in good nature. JPRO cannot be held responsible if this info doesn’t resolve a issue or provide a solution to a problem.
New Q-SYS Monitoring Plugin for JBL SRX900 Series
JBL is excited to announce the immediate availability of a new Q-SYS plugin for JBL SRX900 Series Powered Loudspeakers.
The new plugin integrates all JBL SRX900 models into the 3rd party Q-SYS system and provides high-level access to critical parameters for real-time monitoring and system supervision.
Features include:
• Over 100 parameters include: hardware status, metering, and fault monitoring
• Control of Gain, Mutes, Standby and the Signal Generator
• Integration into Q-SYS event logging functionality
• Side-by-side integration with JBL Performance Software
NOTE: JBL Performance Software remains the core programming tool for SRX900 systems but can co-exist with Q-SYS for monitoring.
The content provided is offered in good faith. While JPRO strives to provide accurate and helpful information, we cannot be held liable if the provided content does not successfully resolve an issue or offer a solution to a problem.
JBL Pro CBT1000 custom tuning file for IT43500HD amplifier
This tuning file is adopted from JBL CBT1000 tuning files and added to an IT4x3500 Device and Preset file. These can be used in Harman Audio Architect or JBL Performance Manager. Within Performance Manager this file can be mixed with VTX-B18 and VTX-G28 by adding a customer speaker and importing these tuning files.
The content provided is offered in good faith. While JPRO strives to provide accurate and helpful information, we cannot be held liable if the provided content does not successfully resolve an issue or offer a solution to a problem.
The content provided is supplied in good nature. JPRO cannot be held responsible if this info doesn’t resolve a issue or provide a solution to a problem.
